Durable garden paths are not just a question of the right surface material - it all comes down to a professional substructure. There are also a few important points to consider when using different plaster materials.
Table of Contents Table of Contents
- How do you create a stable garden path?
- Create garden paths out of gravel or gravel
- How do you create garden paths with bark mulch?
- Comparison of materials for garden paths
- Examples of garden paths with different materials
- How do you create a stable garden path?
- Create garden paths out of gravel or gravel
- How do you create garden paths with bark mulch?
- Comparison of materials for garden paths
- Examples of garden paths with different materials
Paths shape a garden just like the plants in it. It is therefore worthwhile to think carefully about the routing and choice of materials before creating a garden path. If two areas are to be connected directly, straight lines are useful. A curved path can encourage a walk that leads past highlights such as a beautiful plant or a special piece of decoration. Thanks to sophisticated manufacturing processes, concrete blocks are becoming more and more similar to natural stones. Gravel or mulch also blend in harmoniously with the overall picture. Just like small stones, they are easy to lay in curves; large slab formats are ideal for paths that run straight ahead.
Creating garden paths: the most important points in brief
Most garden paths require a base layer of gravel or mineral mix. In the case of paved or paved paths, it should be about 15 centimeters thick. This is followed by a three to four centimeter thick layer of paving sand or grit. For garden paths made of gravel or chippings, a water-permeable weed fleece is recommended over the base course. Bark mulch paths usually do without a base layer.
For most garden paths, the installation of a base course is necessary, as otherwise the paving will gradually settle and shift, and dangerous tripping hazards can arise. In the case of paving stones or paved paths, a 15 centimeter thick layer of gravel or a so-called mineral mixture is first spread over the well-compacted subsoil. The layer thickness is sufficient for light loads such as a loaded wheelbarrow. Mineral mixture can be compacted better than gravel, as it contains not only larger boulders but also fine-grained fractions. A gravel base layer, on the other hand, has the advantage that it is more permeable to water. If the path is to be used occasionally by car, the base layer must be at least 20 centimeters thick. The actual base course is followed by a three to four centimeter thick layer of paving sand or chippings, which compensates for unevenness in the substructure and serves as a paving bed for the road surface.
Tip: On loamy soils, it is important to install a so-called frost protection layer under the base course that is at least ten centimeters high. It usually consists of a sand-gravel mixture with a grain size of 0/32. The frost protection layer must only contain a very small proportion of cohesive components so that it does not develop capillarity and the soil water cannot rise in it. Otherwise, water accumulation in the subsoil could lead to the pavement freezing up.
In order to close the joints, simple filling sand is usually slurried with water on concrete stone coverings. In the case of clinker pavements, so-called crushed sand is usually used as the filler material. The angular grains of sand tilt and give the clinker pavement a good lateral hold. For natural stone coverings, crushed sand or special paving joint mortar based on synthetic resin are also used. It makes the surface waterproof and prevents weeds from growing. While tile coverings are usually stable even without a lateral end stone, a border is recommended for smaller stones. For this purpose, larger paving stones or special curb stones, so-called lawn borders, are laid in a concrete bed or at least fixed on the outside with a so-called back support made of concrete.
Even if you want to create gravel or gravel paths, the installation of a 10 to 15 centimeter thick base layer made of a mineral mixture is advantageous. It prevents the surface material from mixing with the soil. In addition, the base layer inhibits the emergence of weeds, which you can support with a water-permeable weed fleece. A five-centimeter-high layer of gravel or chippings is sufficient for the surface. The finer the grain, the easier the path is to walk on. Chippings are more suitable than gravel, as the angular pebbles tilt and give less when they occur than the rounded pebbles. If the material is to be kept cleanly separated from adjoining surfaces, large stone paving stones laid in concrete can be used as edge delimitation. A filigree alternative are metal edges embedded in the floor.
Bark mulch paths manage on loose sandy soil without a base layer. You simply dig a hollow about ten centimeters deep and fill it with the road surface. In the case of heavy clay soils, the channel is laid 20 centimeters deep and half filled with filling sand so that the mulch layer dries off faster after rainfall.
The local building materials trade offers a good overview of typical regional materials. The following table summarizes the important advantages and disadvantages of the various path materials. The material costs are guide prices that also take the base course into account.
Material type | Material costs per square meter | advantages | disadvantage |
|---|---|---|---|
Concrete pavement | 12-40 euros | Available in many forms, inexpensive, easy to lay | often unsightly patina on simple models |
Natural stone | 30-75 euros | natural look, durable, versatile | Time-consuming laying, large pavement difficult to walk on, expensive |
Paving clinker | 30-60 euros | durable, very easy to care for, easy to walk on, natural look | often deposits of moss and algae in the shade, expensive |
Concrete slabs | 16-40 euros | Versatile, high-quality panels are easy to care for | large formats difficult to lay, patina often unsightly |
Natural stone | 30-80 euros | natural look, often even more charming due to patina, durable | difficult to lay, moss deposits in the shade, expensive |
Gravel / grit | 6-12 euros | easy to build, natural look, cheap | Difficult to drive on, occasional repairs are necessary |
Bark mulch | 2-5 euros | easy to build, ideal for small paths in the bed, inexpensive | difficult to drive on, annual refilling is recommended |
Of course, garden paths can also be created from a combination of different materials, for example from gravel or bark mulch with concrete or natural stone slabs embedded in them. You can find a few inspirations for planning your own paths in the garden in the following picture gallery.
+8 Show all Paths to Inspiration (10) 
MSG / Bettina Rehm-Wolters The pebble step plates go nicely with the agaves
MSG / Patrick Hahn The thick wooden planks act like a natural bridge in the gravel path
MSG / Martin Staffler The path out of the large, light pebbles leads elegantly between the herbaceous beds
MSG / Alexandra Ichters Un jointed natural stone slabs grow in over time and become a natural garden path 
MSG / Bettina Rehm-Wolters The curved path made of cobblestones looks particularly lively
iStock / rodho The square plates of the path create a nice contrast to its curved course
iStock / Antoninapotapenko The round wooden step plates can also be used to create a staircase through the bed on the slope
iStock / eurobanks Bark mulch is reminiscent of forest floor and has a particularly warm and natural effect. The step plates were laid between them seemingly at random
